Used and Surplus Pulse Jet Cartridge Dust Collectors

Bottom load filters. Designed for (6) filter elements. Maximum filter length would be 57". (No filters included). With mounted solenoid enclosure, timer enclosure with photohelic gauge, and Siemens fused disconnect safety switch. 10"Ø flanged dirty air tangential inlet. 10"Ø flanged clean air outlet in top center of unit. 8"Ø flanged material outlet in hopper. Manual rotating lump breaker installed in hopper. 58" of clearance below hopper flange. *Note- Three damaged right angle valves which will need to be replaced prior to use. 50" Ø housing. Overall dimensions: 54" Wide x 70" Deep x 194" high. Fan not included.

Stainless steel, insulated modular housing, space-saving design
Dust-laiden process air inlet plenum with 24" square duct opening
Clean air plenum with compressed air header and solenoid valves
Top-installed 2HP centrifugal fan (3490RPM)
Filters: quantity of two- pleated cartridge filters (front side removal)
Collector has an overall height of 163" and a base footprint of 44"W X 23.5"L
Total Filter Capacity: 650 Sq/ft
Process air capacity: 600CFM
Rated for 7.20" w.g.
Solids discharge to a manual dump pull-out drawer (drawer not included)
Installed with a Fike flameless explosion vent
Supply Power: 230/460V, 60Hz, 3ph
Video Available

Designed for 21 pleated 24" tall cartridges. Collector currently is without 6 of the 21 cartridges. 45" diameter with overall height of 48". Currently does not have any blowpipe headers, timer or solenoid valves. Unit has 4.5" O.D. Clean air outlet plain end. Fan not included.

(14) pleated cartridge filters which measure 58" long. 5-1/2"Ø dirty air inlet and clean air outlet. 18"Ø flanged material outlet in hopper. 49" of clearance below hopper outlet. Overall dimensions: 38" Wide x 48" Deep x 165" High. Fan not included.
22-1/2" cone height (bottom of side wall to outlet flange)
115" from bottom outlet Flange to Top

( approx 1800 CFM ) model 900, series 343 Dynamic Air Modu-kleen bin vent cartrige pulse jet filter . Unit has 9 filter elements. Weight of unit is 1,000 lbs. Dimensions are 63" x 63" x 57" tall. Unit is designed for side removal of cartridges. Carbon steel construction. Unit has two doors 180° apart. No timer or blow pipe header. Fan not included.

Steel and aluminum cylindrical dust collector. Top removal design.  Aluminum clean air plenum. Carbon steel material contact side.  44 cartridges currently installed and are approx 44" long. 7 Solenoid pulse jet header complete with Dwyer Magnahelic pressure guage, timer and Solenoid valve box.  6" material inlet; 14" hopper bottom outlet and 8" diameter clean air plain end plenum outlet.  Design pressure 14.5 psig; temp 150° f.  Weight of unit is 3,003 lbs.  Design capacity 50.5 cubic feet bottom hopper. Manufactured by Rage Inc., Plumsteadville, PA. 48"ø housing. 103" sidewall from tube sheet to top of cone. Aluminum clean air plenum measures approx 14" H. Fan not included.

Manufactured by Rage Inc, Plumsteadville, PA. Design pressure 14.5 psig, design temp -15 to 150° f. 50.5 cubic feet storage capacity, weight 2,968 lbs. Unit has aluminum clean air plenum with seven blow pipes. 48" diameter. Designed for top removal of cartridges. Overall height is approx 152". Bottom cone is boltable and removable. Bottom outlet is 8" diameter flanged. Cone has eight connections for air pads. Unit has 6" inlet dia and 8" clean air outlet. Collector is currently missing control timer and solenoid valves. We can rebuild for additional cost. Material contact side is carbon steel. Clean air side is aluminum. Tube sheet is carbon steel. Unit has 37 used filter cartridges installed.

Designed for (43) bags and cages. Bottom load. Hopper is currently disassembled for shipping purposes. No fan included.

Height- 18' x deep- 8'-8" x wide- 6'-2", 48" housing, 21" hinged access door, 18"x 40" flanged material outlet, 8" clean air out, 33"x 35" explosion panel, (21) 6"x 56" long pleated cartridges, 12"x 16" bolted access panel, (2) 6" diameter dirty air inlets with (2) air actuated butterfly valves.
Fan not included.

Mild steel construction with 1" thick insulation throughout the housing
Bottom hopper with Ø6" manual swing gate
Inlet/Outlet: Ø12" flanged 90° elbows (rotatable)
Houses two- 22" dia. X 24 3/4"long high-temperature pleated filters (not included)
Footprint of the base: 28.25"W X 38.25"L
Overall dimensions: 54x32x123"
Weight = 697 LBS
General Arrangement Drawing Available

The Modu-Kleen bin vent/dust filter is controlled by solid state electronics, and is self-cleaning for minimum maintenance.
Built as an integral part of the filter housing, the reverse air nozzle directs a shock wave down the entire length of the cartridge during the cleaning cycle. This shock wave improves the Modu-Kleen bin vent/dust filter's efficiency when compared to other venturi type dust collectors that direct the shock wave over only a portion of the filter media. The filter cartridges are cleaned one row at time, so the Modu-Kleen bin vent/dust filter Series 343 and 352 can operate continuously. There is no need to shut down for cleaning.
No filters included. The collector will require (5) cartridge filters; each measuring 5.5"Ø x 36" long
48"Ø housing x 39" straight side. Overall height = 7'
60° cone with 3" of clearance below outlet.

The Modu-Kleen bin vent/dust filter is controlled by solid state electronics, and is self-cleaning for minimum maintenance.
Built as an integral part of the filter housing, the reverse air nozzle directs a shock wave down the entire length of the cartridge during the cleaning cycle. This shock wave improves the Modu-Kleen bin vent/dust filter's efficiency when compared to other venturi type dust collectors that direct the shock wave over only a portion of the filter media. The filter cartridges are cleaned one row at time, so the Modu-Kleen bin vent/dust filter Series 343 and 352 can operate continuously. There is no need to shut down for cleaning.
No filters included. The collector will require (5) cartridge filters; each measuring 5.5"Ø x 36" long.
48"Ø housing x 39" straight side. Overall height = 7'
60° cone with 3" of clearance below outlet.

All mild carbon steel construction. The filter chamber is 48" diameter X 96" tall. Holds 21 pleated cartridge filters, side-mounted filter access panel, and air header. Tandem 6"Ø inlets installed with pneumatic butterfly valves for static pressure control. 8"Ø flanged outlet with sleeve adapter. Bolt-on bottom hopper with access panel having an 18" X 40" flanged particle discharge. Assembled overall height is 154". Includes complete set of cartridge filters.

designed for 10" dia. X 18" L. Cartridge filter. (new filter required) 5" Cincinnati Fan model pb-9, S/N 700443-1, cast aluminum centrifugal blower driven by a Leeson washguard 1/2hp, 3450 rpm, direct drive motor. Collector housing is 18"sq. X 36" H. W/8" dia. Bottom inlet and removable front access panel. Includes control panel and timer enclosure. Previously used to vent a bulk bag unloader.

Shop # 11962-1. Customer # eng-043. Serial number HW3998. Year built 1994. Design temperature = 100°f. Drawing on file.