Used Other Filters

Serial No: H-0012701Z
Stainless steel covered U-trough using a combination of drainage, compaction and dewatering.
8"Ø double-flighted, shaftless helical auger with ½" bottom wear liner.
Sludge Capacity: Approximately 157 Cu/Ft per hour
24" long wedge-wire screen compaction zone with spring-hinged end discharge door.
Product Inlet: 19" X 24" flared hopper with safety grate
Some adjustment for the incline, unit shown at 24°, discharge height at 5'-0" above floor.
Sanitary flanged run-off liquid drains.
Powered by a 3HP gearmotor (pre-wired for 460V, 60Hz with hazardous location protection).
Max. Working Speed (auger): 26RPM
Attached to a 36" X 46" portable base assembly.

Serial No USA 1001.
Material Of Construction: 316L stainless steel (shell & candle filters)
For clarification of various liquids with low solids content.
Vertically arranged, slotted candle filter elements with replaceable filter medium.
Efficient blow-back/backwashing, completely closed system, outside to inside flow.
Cake Holding Capacity: 220 liters @ 20mm thick
Total Filter Area: 8m sq. (86 sq. ft.)
Filtration Rating: approx. 5 micron
Cake Discharge (bottom): 14"Ø electric actuated butterfly valve
Shell Design Pressure: 4.5Kg/cm
Shell Design Temperature: 80°C
No controls available, structural support required.
General Arrangement Drawing on file (metric).

Nominal Capacity: 2.78GPM
Max. Pressure: 100-125PSI
Module Vessels: 4"Ø X 40"L (qty: 2)
Pump: 2HP stainless steel.
Approximate system recovery of 50%.
Culligan digital touch controller.
Mild steel frame assembly (20"W X 31"L X 53"H)
System requires 208-230V, 60Hz AC power
Some parts are damaged. See photos.

Serial No USA 1001.
Material Of Construction: 316L stainless steel (shell & candle filters)
For clarification of various liquids with low solids content.
Vertically arranged, slotted candle filter elements with replaceable filter medium.
Efficient blow back/backwashing, completely closed system, outside to inside flow.
Cake Holding Capacity: 220 liters @ 20mm thick
Total Filter Area: 8m sq. (86 sq. ft.)
Filtration Rating: approx. 5 micron
Shell Design Pressure: 4.5Kg/cm
Shell Design Temperature: 80°C
No controls available, structural support required.
General Arrangement Drawing on file (metric).

This is a custom build project that will require some additional design and fabrication to complete.
Constructed with 11 gauge stainless sheet and a mild steel support frame. Slurry is fed into the top of tank end. It is then agitated and mixed by 3- powered horizontal drums. They are driven by a pair of 2HP gearmotor/chain drives. Solids that fall into the 8"Ø auger is then conveyed across a perforated screen. Particles then drop into a 4"Ø bottom auger to be extracted from the tank. The separated liquids spill out of the rear of the tank by an 8" X 48" spillway. The construction on the solids conveyors has not been completed on the discharge end and will require drives on the oposite ends. There are additional augers, trough and screen sections included with purchase.

Cast stainless steel (316) housing and cover
Rated for: 275PSI @ 100°F (for continuous use)
Quick-open cover with o-ring gasket
Length between flange face: 11.18"
Straining element not included
Connections: 4"Ø ASME Class 150

44" diameter. 1/2" thick plastic walls with an additional 3/16" thick liner. Total wall thickness = 11/16". Lid is 3/16" thick. Inside of tank is stainless steel spreader bar for pick up with clevis hooks. Tank is manufactured with a perforated plastic plate covered by a fine screen filter. 3/4" holes in perforated plate. The screen is located 19" from top of tank. The screen is 24" up from the bottom drain. The tank is setting on a 45" square steel platform that is 12-1/2" tall. 2" diameter pvc outlet. 5" diameter vent hole. Overall height w/ platform = 68".