Used and Surplus Other Heat Exchangers

Bryan CL Series Flex Tube Boiler for Hot Water Heating
National Board No: 31124
Max. Working Pressure: 60PSI
Relief Valve Setting: 30PSI
Heating Surface Area: 360 sq. ft.
Natural Gas Connection: 2"NPT
2HP centrifugal blower fan (3450RPM)
Control Circuit Voltage: 120VAC, 1ph
Motor Circuit Voltage: 208VAC, 60Hz, 3ph

Bryan CL Series Flex Tube Boiler for Hot Water Heating
Max. Working Pressure: 60PSI
Relief Valve Setting: 30PSI
Heating Surface Area: 360 sq. ft.
Natural Gas Connection: 2"NPT
2HP centrifugal blower fan (3450RPM)
Control Circuit Voltage: 120VAC, 1ph
Motor Circuit Voltage: 208VAC, 60Hz, 3ph
Overall dimensions: 139" L x 39" W x 84" H
Weight = 4,758 LBS

Constructed of all stainless steel material
Elevated U-trough design, double flanged with stiffener ribs and hinged full-length covers
Trough bottom is also installed with steam diffusers and temperature sensors along the length
Steam enters into a pair of 2"Ø headers two-zone (fore & aft) bottom trough injection ports
Steam also is supplied thru a rotary joint into the Ø8" hollow shaft of the auger through a series of perforated holes along the shaft
Product is metered into the trough with an installed stainless steel 24" X 8" rotary feeder on the drive end
It is then conveyed by the auger through the steam bath to a flanged discharge (53" from floor elev.)
The continuous welded flighting has a nominal thickness of 5/32", and is pitched at 12"
Length of material conveyed: 16'-8" between inlet/outlet centers
Powered by a 2HP gearmotor/chain reduction drive (auger)
Supply: 230/460VAC, 60Hz, 3ph
Unit will require a process steam source

Quench air heat exchanger unit for cooling a fluid stream using ambient airflow
Leak-proof operation to 450°F
Design Pressure: 100PSI
Removable, floating headers with 2"Ø ANSI 150 class flange media connections
Tubes: Twenty- 1"O.D. SA-214 steel, 0.060" wall, 24" long (straight) with aluminum fins
Cooling air provided by a 1HP, 20" diameter direct drive fan
Supply: 230/460V, 60Hz, 3ph
Operation manual of file
Shipping info: One skid, 36x36x46
Weight = 478 LBS

Hunter 120,000 BTU/HR Multi-Fuel Space/Tent Heater
Model No: MTH-150
Serial No: 0607
Volts: 120V

The MTH150 tent heater is a portable, medium-capacity outdoor heater with heat output of 120,000 BTU/H at 1,900 CFM (35.17 kW at 3,228 m3/h). The MTH150 uses 120-volt power and burns all grades of diesel fuels, including military JP8. Fuel tank capacity is 22 gallons (83.3 liters). With fuel consumption of 1.25 gallons per hour (4.7 liters per hour), the MTH150 has the ability to run for extended time periods with a full tank of fuel.

Features include:

Remote room thermostat
Carbon monoxide detector
Stackable/lockable
Low maintenance and reliable operation

Hunter 120,000 BTU/HR Multi-Fuel Space/Tent Heater
Model No: MTH-150
Serial No: 0700
Volts: 120V

The MTH150 tent heater is a portable, medium-capacity outdoor heater with heat output of 120,000 BTU/H at 1,900 CFM (35.17 kW at 3,228 m3/h). The MTH150 uses 120-volt power and burns all grades of diesel fuels, including military JP8. Fuel tank capacity is 22 gallons (83.3 liters). With fuel consumption of 1.25 gallons per hour (4.7 liters per hour), the MTH150 has the ability to run for extended time periods with a full tank of fuel.

Features include:

Remote room thermostat
Carbon monoxide detector
Stackable/lockable
Low maintenance and reliable operation

Hunter 120,000 BTU/HR Multi-Fuel Space/Tent Heater
Model No: MTH-150
Serial No: 0607
Volts: 120V

The MTH150 tent heater is a portable, medium-capacity outdoor heater with heat output of 120,000 BTU/H at 1,900 CFM (35.17 kW at 3,228 m3/h). The MTH150 uses 120-volt power and burns all grades of diesel fuels, including military JP8. Fuel tank capacity is 22 gallons (83.3 liters). With fuel consumption of 1.25 gallons per hour (4.7 liters per hour), the MTH150 has the ability to run for extended time periods with a full tank of fuel.

Features include:

Remote room thermostat
Carbon monoxide detector
Stackable/lockable
Low maintenance and reliable operation

Continuously-fed steam heated processor with all stainless steel material contact surfaces
Flared u-trough design with an 8"Ø X 12" long sanitary type auger with end disconnects for ease of cleaning
Square-shaped outer jacket
Full length top cover that is hinged and jacketed
14" square product inlet
End discharge (needs flange)
Will require an under-mounted gearmotor (5HP), sprocket, chain, pillow block bearing, guard, and steam source

Contact us for more information.

Model WMC250DSC-ER10

BURNER INFO: Ovenpak 400 Gas Burner (Size 432M) 2,250,000BTUH
MAIN FAN INFO: 112HP Sodeca high pressure centrifugal fan with backward-curved impeller made of galvanized sheet steel 19,776CFM (max. @ 3564RPM) 460V, 60Hz, 3ph
48'' diameter x 13' L Combustion Chamber
Flame Control Panel
Natural Gas Train Assembly (1 1/2" pipe size)

Model: 6X9
Bottom entry tangential product inlet, top outlet
Steam or liquid media heating or cooling (counter-current media flow)
PRODUCT CHAMBER [each unit]
Surface Area: 9 Sq. Ft.
Design Pressure: 450PSI
Design Temp: 315°F
MEDIA CHAMBER [each unit]
Design Pressure: 225PSI
Design Temp: 315°F
INDEPENDANT DRIVES: 10HP with inline gear reduction
Supply Power: 208-230/460VAC, 60Hz, 3 ph (both units will require 28.4amps @ 460V)
Column support with pedestal base mounting

Serial number: M02820-08/CW. Overall dimensions: 84x84x76. Weight = 2,795 lbs.
High Purity De-Ionized Water Temperature Control System
Equipment is designed to cool 20 GPM of highly purified water to 18° C +/- 2° at incoming DI water temperatures between 50° F and 75° F. Temperature control will be achieved through indirect cooling of the DI water using a double walled, plate and frame heat exchanger with process water that modulates between 50° F and 70° F. Precise DI water temperature control is achieved through the use of a 3-way valve on the process side of the heat exchanger using a PID loop controlled from the leaving DI water temperature. This equipment consists of the following:
(1) Temperature Control Skid complete with the following:
• (1) 8.5 ton air cooled refrigeration unit, model DE10ACOD. The unit shall have a capacity of 8.5 tons of refrigeration operating at an entering condenser air temperature of 95° F. Includes the system circulation pump and all operating controls for the refrigeration unit.
• (1) Double Walled Plate and frame heat exchanger with 58.13 ft2 surface area designed to provide heating/cooling of the DI water at a 5° F approach to the process water temperature. Plate material will be type 316 stainless steel with NBR gaskets. This heat exchanger is designed for use with highly purified DI water and includes passivated and electro polished plates with 2" tri-clamp connections on the DI water side of the heat exchanger
• (1) 3-way modulating temperature control valve for precise DI water temperature controlled from the leaving DI water temperature
• (1) 45 kW Circulation heater designed with Incloy elements
• All process piping and fittings will be Type L Copper and each component will include quick connect unions to allow for the quick change of individual system components.
• All skid components will be painted blue with primer and 2 coats of industrial grade enamel paint.
• All interconnecting piping will be insulated with 1/2″ Armaflex insulation.
• (1) System Control Cabinet will be mounted to the temperature control skid. All power and control wiring connections to the temperature control skid will be with quick connect plugs to facilitate the change out to the stand-by skid with minimal downtime. Includes the following:
• NEMA type 4 rated.
• 750 VA Control transformer for single point electrical feed.
• Fuse blocks and contactors for the chiller and SCR controller for the heater.
• (3) Temperature Transmitters
• Allen Bradley MicroLogix PLC for complete system control
• MoniTouch HMI operator interface
• Alarms consisting of high and low temperature
• Auto / Stop selector switch.
• Panel Mounted Non-Fused Disconnect

UNIT IS UNUSED. SERIAL NUMBER A0539094. NATIONAL BOARD NUMBER 11213. BUILT IN 2006. SIZE "C" H. D. VAPORIZOR. DRAWING NUMBER 11950.B AND 30019-D, REVISION C. DESIGNED FOR 150 PSI AT 300 F BOTH SHELL AND TUBESIDE. TEST PRESSURE AT 225 PSI. ORIGINAL APPLICATION DESIGN WAS TO VAPORIZE 853 POUNDS PER HOUR OF SULFUR DIOXIDE ON SHELL SIDE USING 160 POUNDS PER HOUR OF 15 PSIG STEAM ON TUBESIDE. COMPLETE DOCUMENTATION IS AVAILABLE INCLUDING DRAWING, U-1 FORMS, MILL CERTIFICATIONS, ETC. SHELL IS 6" DIAMETER NOMINAL PIPE SIZE X 5'-2-7/16" LONG SA-106 GRADE B (CARBON STEEL ) MATERIAL OF CONSTRUCTION. TUBESHEET IS SA-516A GRADE 70 (CARBON STEEL ). TUBES ARE 1.05 INCH OD AND CONSTRUCTIED OF SB-619 N10276 ( HASTELLOY C-276) MATERIAL.

DESIGN PRESSURE: 180/-15 PSIG, DESIGN TEMPERATURE: 300° F, TEST PRESSURE: 225 PSIG. MATERIAL: PIPE: SA-53 GR B, FLANGES: SA-105, RETURN BENDS: SA-234 GR WPB, FIN STOCK AND STRUCTURAL FRAME: CARBON STEEL. COOLER FRAME MEASURES 13.5"W. X 14'-6"L. X 4'-0"H. 3" DIA. ANSI 150 RAISED FACE FLANGED INLET AND OUTLET CONNECTIONS. PDF DRAWING ON FILE.

Lot of 2… one- reducing elbow (6"x3"), one- reducing tee (6" x 6" x 3"). Fitted with steel band couple sleeves.

Lot of 4. These items appear to be unused but have some light rust on flanges. Steel flanged with ceramic tubesheet insert w/ 0.75" dia. Holes. For 6" dia. Pipe/tube, has 11" O.D. Flange.

Job#52171. Unit type: Thermo-T. 304 ss plates that are.031" thick. Manufactured by Des Champs Technologies (natural bridge station, va). Model 81MUI703450-BAB. Serial number 52171A; job # 52171, poca, wv job. Overall dimensions: 65" W x 94" long (not counting transition) x 55" H. Show and tell video on file.

Thermo-Z unit type. Job #35125. Unit model #81mui-944743-.50/.50-304l . Plate area made of 304 ss that are .031" thick. Overall dimensions: 6'-3" wide x 10'-1" long x 65" high. 43"x47" inside. (42) ½' wide plates

Item has 390 tubes, 0.25" diameter, 30" long
63.8 square feet of surface area
Dimensions of heat exchanger section is 30" x 11.5" x 4"
Saturated steam up to 281°F and 35 psig

Budzar Industries Water Heater System
Model No: 1WT-930-DSP
Serial No: 200901-14797
Field Wiring Diagram: B14797-ES
Largest Motor HP: 1.5 HP
Enclosure Type: 12
460 Volt, 3 Phase
Rapid Exchange Time: 1 min/cu.ft.
Purge Control Accesory Model No: EPV-2-SA
Pro Flo Water Heater Safety Tank - Model No: PFT5
Precharge pressure: 40 psi, Max Operating Temp: 200° F, Max W.P.: 150 psi
(2) 1.5" Swagelock Connections, extend 9" out from unit
(2) 1" Water Connections, extend 7" & 19" out from unit
Overall Dimensions: 45" L x 35" W x 35" H.
Manual on File.

Creamery Package Dairy Food Processing Equipment
Votator style scraped surface heat exchangers
Serial No: 30-2456
(3) 8" Ø x 28" L Knife Carriage
(8) 13" Blades on each carriage
Temperature and pressure instrumentation
2" Sanitary connections on front of unit
Overall dimensions: 93" L x 60" W x 63" H
Manufactured by Creamery Package Mfg. Company.
(Producer also supplied for creameries, cheese factories, milk dealers, dairymen, and ice cream makers, refrigerating and ice-making machinery, egg cases and fillers.)
3HP inline gearmotors with chain reduction for powering inlet/outlet pumps
20HP belt drives (3) for powering the scrapers
Power supply: 208-230/460V, 60Hz, 3 phase

Stainless Steel Ter Braak Votator Heat Exchanger
Type: 5700
Number: 22
230/460 Volt WEG Motor
*Manual brake knob not operational, 3HP AC Tech Variable Speed Drive included
VFD Specs: Model No: M1230C, Type 4, 3 HP, 2.2 KW, Input: 200/240 3 Phase, Output: 0-200/230 3 Phase
(2) 4" Ø Screw Augers
8" x 8" Inlet & Outlet
1.5" Sanitary Connection on Driven End
4" Sanitary Connection on Non-Driven End
10" Stainless Steel Oval Housing
1" Fluid Quick Connects
Overall Dimensions: 106" L x 36" W x 55" H
Demonstration video on file.