Used and Surplus Batch Mixers

Total Capacity: 0.50 Gallon, Working Capacity: 0.25 Gallon. Manual side dump tilt over bearing journal discharge. Jacketed mixing chamber suitable for steam, water or hot oil operation. All stainless steel product contact parts. 1/2HP, 208-230/460 volt, 1725RPM, 60Hz, 3 phase. Overall dimensions: 22"W X 42"L X 46"H. Weight: 380lbs. Demonstration video available.

Stainless steel mixing chamber with welded-on carbon steel flanges. The straight section is 14"Ø X 5" long. The assembled length of the chamber is 15". The three sections and end covers are clamped. Installed intensifier bar with blades chain-driven by a 1/2HP, 1725RPM, 115/230 volt, single phase AC drive. The blender is chain-driven by a 1/6HP, 115 volt split phase gearmotor. Shipping Info: 48" X 40" X 55" 341LBS

With intensifier bar!
Design Capacity: 3 cubic feet @ 125 LBS per cubic feet
All stainless steel material contact surfaces
Mild steel frame with protective cage
Blender Drive: 3/4HP, 208-220/440 volt, 60Hz, 3 ph
Intensifier Bar: 3/4HP, 208-220/440 volt, 60Hz, 3 ph
6"Ø manual butterfly valve discharge
Demonstration video on file.

Type B35OH. Model 227294. 35" wide X 24" deep dump catch bin which hydraulically tilts and loads the mixer. Hand operated valve for liquid addition. Approximately 8-10 cubic foot capacity. Demonstration video on file. Overall dimensions: 92x62x96. Weight = 1481 lbs.

8 Cubic Feet Paul O Abbe Stainless Steel Double Ribbon Blender Mixer
Model No: 5RM
Serial No: A19624
Tested Jacket Rating: 40 PSIG Hydrostatic
Working Pressures: Internal - Atmospheric, Jacket - 14 PSIG
Carbon steel outer jacket and support frame
Stainless steel tub liner, shaft and ribbons.
Mixing tub dimensions: 18"W X 50"L X 22" deep.
Handwheel actuated rack & pinion dump gate.
2 HP Baldor Motor: 230/460 Volt, 3 Phase, 1750 RPM, Frame: 145TC

Stainless steel blender shell. Power: 230/460 volt, 60Hz, 3 phase. Demonstration video on file.

Serial number: 35714-1305. 13 cu/ft working capacity. Stainless steel material contact surfaces, carbon steel jacketing. Vent port: 8"Ø flanged, Charge port: 10"Ø flanged, Discharge port: 16"Ø flanged with manual dump valve. Demonstration video on file. Overall dimensions: 92" long x 53" deep x 104" high. Weight = 3,829 lbs.
Input and output shafts of gearbox are both 2-1/8"Ø
Ratio = 9:1

Dry storage conical hopper (12GA. rolled & formed stainless sheet)
One-piece cover with bracing and hinged lid
36" diameter with 10" straight side and 11" flanged outlet
Slope of the cone is approximately 60°
2"Ø FMTP side port (low level indication)
Lower level sight glass (sealed)
Top-mounted, geared agitator drive 460VAC, 30-60Hz, 3 phase
11RPM agitator speed @ 60Hz

Maximum density of 30#/cf. Max design pressure on shell is 15 psig and full vacuum. Max design temp 250°f. 460 volt 3 phase. 60 cycle. 16" inlet and 6" discharge. Serial number is pk#156399. Designed for full vacuum and jacketed. Motor baldor 1 hp, 208-230-460, 1725 rpm. Jacket is carbon steel; shell is stainless steel. With mounted hot oil package with includes centrifugal pump and electric heater.

Serial number: 18654. Blender has a total volume of 32c/f , 21c/f working volume (60%). All carbon steel construction, heavy-duty elevated base frame, fully covered bull gear guard. 14"ø inlet with locking cover, material outlet has an installed 8"ø fmc syntron iris valve and a discharge height of 56". Included control enclosure with start/stop, jog, forward/reverse controls. Powered by a 7.5hp, 1745rpm, 208-220/440v, 60hz, 3 phase westinghouse motor with electric brake. Inline gear reducer with a 13.95:1 ratio. Base dimensions: 3'-6" W. X 6'-9" L. With an overall height of 9'-8".

3 HP Drive with 15:1 ratio.
Rotation speed = 40 RPM
Demonstration video on file.
93" x 42" footprint
48" of clearance below outlet.
19"Ø inlet (manual swing door, locking)
10"Ø outlet (manual butterfly valve)

All carbon steel construction. 48"Ø mixing hopper fixed to elevated stand. 12"Ø auger powered by 5HP gearmotor (requires 230/460VAC, 60Hz, 3 phase). Demonstration video available.
Overall dimensions: 75"x75"x128" tall

30 HP reliance electric motor, 1765 rpm, 230/460 volt. Foote-jones gear reducer, 38.4:1 ratio. Gear drive with guard. 12"ø flanged outlet with air actuated bray butterfly valve.
Total volume 375 cubic feet.
Working Volume 225 cubic feet.
The double cone has 36" x 24" pad feet. The outside footprint of the feet are 9'-10" deep x 16'-9" wide.
Blender shell has been untrasonic thickness tested: Cones (both) 0.321" thick; cylinder: 0.620".
There is about 1' of clearance below the outlet as it sits.
Overall dimensions: 17'-0" wide x 9'-10" deep x 11'-2" high.
Final drive speed 6 RPM.

Gear drive with guard. 9'-2"ø chamber with a 38" straight side. Half cone length is approx 48". 45° cone. Current height = 13'-9". 90" high pedestals. Pedestal footprint is approx 14' wide x 16' deep. 10"ø flanged outlet.
Total volume 400 cubic feet.
Working volume 250 cubic feet.
• blender shell is constructed of 304 stainless steel. It has been untrasonic thickness tested: Cones (both) 0.255" - 0.269" thick; mid-section cylinder: 0.395" thick.
(4) load cells included!

Stationary mixer, 270 cubic feet for concrete or other material.
Motor: 40 HP, 460volts, 1770RPM

S/N 130517. Max material density is 165 lbs per cubic foot. Shipping info: One skid, 55x50x78. Weight = 653 lbs. Demonstration video on file.

Serial number: 1781928. Comes with all the attachments and accessories shown. 1hp, 208 volts, single phase, 60hz.

Custom built by Virginia Tech Department of Wood Research. The atomizer was purchased new in December 2003 from Coil Manufacturing, Model EL-3. Unit is basically a rotating drum with internal baffles to tumble the product being held in the rotating drum. Designed for liquid injection through spray nozzle for mixing liquid into solid. Spray nozzle manual on file. Drum is manufactured of corrosion resistant material. Drum has a plexiglass door for viewing, inserting and removing product. Drum is driven by two axle tire arrangement with variable speed drive. Drum is 6 feet in diameter and 39" deep = ~90 feet³ Several controls also included. 230 volt 2 HP explosion proof DC variable speed drive included. Several more photos on file. The overall dimensions of the machine assembled is 8' - 7" tall x 7'-9" wide x 52" deep.

Two stainless steel 23" DIA X 19" deep mixing pots. Metering pump system with strainer and electric heater for resin temperature control Mix pots are mounted on electric rotatation drive units with stationary plow mixers that are manually moved onto a load cell platform for precise material loading. MIX POT UNITS ARE POSITIONED ON THE 32"W X 48"L PLATFORM SCALE VIA A TRAVELING CONVEYOR SECTION APPROXIMATELY 12' LONG. UNIT SPECIFICATIONS: TEMPERATURE CONTROLLED RESIN, USER DETERMINES RESIN TEMPERATURE FROM 70-140° F, DIGITAL READOUTS TO INDICATE RESIN AND HEATING FLUID TEMPERATURE, RESIN DISPENSING 20 LBS PER MINUTE WITH LOAD CELL ACCURACY, FILL DISPENSING 50 LBS PER MINUTE WITH LOAD CELL ACCURACY, MAXIMUM BATCH SIZE 500 LBS PER BOWL, DIGITAL READOUT TO INDICATE GRAMS OF CATALYST BASED ON RESIN LBS AND CATALYST RATIO, USER FRIENDLY CONTROL PANEL FOR ENTERING BATCH SIZE AND INGREDIENT RATIOS, TOTALIZER FOR TRACKING MATERIAL TOTALS AND INDIVIDUAL INGREDIENT USAGE AT CHOSEN INTERVAL, MANUAL OR AUTO OPERATION SELECTOR SWITCH, TEMPERATURE READY INDICATOR AND SWITCH TO INSURE RESIN IS AT DESIRED TEMP BEFORE MACHINE WILL START. 240V 3PH 60 AMP POWER REQUIREMENT.

24" top inlet
10 HP Super Line Motor: 3 Phase, 460 Volt, 1740 RPM, Frame: 132M
Demonstration video on file.
Total Volume approaches 100 cubic feet. Working volume ~ 50 cubic foot.
• blender shell is constructed of stainless steel with an outer support band made of carbon steel. It has been ultrasonic thickness tested: Cones (both) 0.073" thick; mid-section cylinder: 0.074" thick.
Approx. 52" of clearance below outlet.

Stainless steel blender shell with locking covers. Agitator drive functions but missing crossbar. Runs on 115 volt, single phase AC power. Blender is belt driven, agitator is chain drive. Dedicated motors for blender and agitator.