Used and Surplus Ribbon Blenders

Stainless steel material in contact with product
U-trough mixing chamber with perimeter flange is 21"W X 48"L
Jacketing installed on the u-trough area with 1"NPTF media connections (non-jacketed end plates)
Jacket Rating: 14.9PSI max. (non-ASME)
Hinged cover with 8" X 8" cut-out and hold-down levers
Bolted end plate slots for ribbon assembly removal/maintenance
Product discharge: 5"Ø manual pivot-gate (metal-seated) with 9" X 10.5 skirt, 43" from floor elevation
Footprint of portable base: 34"W X 49"L
Elevation to top cover: 71.25"
Drive: 2HP US Electrical Varidrive (double reduction) & chain reduction drive
Supply Power: 230/460V, 60Hz, 3ph AC
Controls: wired into a fused disconnect & starter with push button start/stop and reversing switch
Demonstration video on file. Ribbon speed = 27 RPM
Overall dimensions: 60" L x 42" W x 80" H.
Weight = 1,260 LBS.

All stainless steel construction
Mixer housing is 21"W X 48"L
Side-hinged cover with pneumatic lift, 7" X 14" inspection opening & 6"Ø vent port
Bolted idle end plate for ribbon maintenance
3.5"Ø pivot-gate discharge, 45.5" from floor elevation
Driven by a 5HP gearmotor & chain reduction drive
Base footprint: 25"W X 44"L
Elevation to top cover: 75.5"
Supply Power: 220V, 60Hz, 3ph AC & compressed air
Weight = 1,521 LBS.

Stainless Steel Ribbon Blender
Blending Chamber Dimensions: 40" L x 32" W x 34" Deep (Working Capacity)
32" Ø x 1/2" Thick Single Shaft Ribbon
Manual Opening Cover
(2) 1.5" Intensifier Bars
15 HP Elektrim Motor: 230/460 Volt, 3 Phase, 1750 RPM, Frame: 254TC
Demonstration video on file.

Stainless steel wetted components with a mild steel support stand
For cooling or heating product- shaft installed rotary joint and jacketed sidewalls of the u-trough. The jacket is low pressure design (~1 bar). A small leak was noted in the interior of the mixer near the ribbon.
Mixing chamber dimensions: 24"W X 60"L X 28"Depth U-trough
Top is fully covered with twin stainless panels, hinged with proximity switch
Product Discharge: 6"Ø manual pivot valve - positioned at bottom center (not flush with mixer)
Mixing chamber is fully welded with packing-gland shaft seals
5HP inline gearmotor with chain reduction, start/stop push button & enclosed motor starter
Blender base footprint is 34"W X 64"L
Weight = 1,649 LBS.
Top Elevation: 71"
Discharge Elevation: 38.5"
Supply: 230/460V, 60Hz, 3ph
Video Available

Approx 36" diameter mixing chamber x 67" long.

All stainless steel construction
Mixer housing is 30"W X 78"L (wall: 0.128" thk.)
Full top cover with hinged panels on each end
Non-rated dimple-plated belly jacket with 3/4"NPT connections (approximately 21.9 sq. ft. surface area)
6"Ø flanged, manual butterfly valve discharge (bottom-center), 37" from floor elevation
Driven by a 5HP gearmotor & chain reduction drive
Ribbon speed = 40 RPM. Demonstration video on file.
Base footprint: 36"W X 100"L
Floor elevation to top cover: 78"
Weight = 2,646 LBS.
Supply Power: 230/460V, 60Hz, 3ph AC

36 cu ft Ribbon Blender - Food Processing Equipment Co.,
Serial # 48008
Unitary mixing chamber 30"W X 60"L X 36" deep (12ga. stainless sheet)
11/2 inch ribbons, 2" shaft with stub end disconnects & seals
6.0"Ø manual gated end discharge & 3"Ø bottom washdown drain
Portable 1 1/2" welded pipe frame with casters
2 HP gearmotor with chain drive
Current ribbon speed = 39 RPM.
Supply power: 208-220/ 60 cycle, 3 phase
Demonstration Video on File.

Horizontal U-trough mixer constructed with welded stainless steel
Mixing chamber is 30"W X 78"L with a total depth of 35"
Top cover with twin door manual dump station, 25" X 48" safety bar grating & 4"Ø ventilation port
Cover installed with pneumatic lift (controls and small repair required)
Drive end of the shaft installed with an 80 tooth sprocket with B style hub
Will require a chain drive with base-mount and guard
8"Ø flanged, bottom-center discharge
Base mounted, 47"W X 84"L area
Weight = 1,894 LBS

Stainless steel wetted components
Mixing chamber dimensions: 35.37"W X 78.75"L X 39.5"Depth
Full top covering with bolted stainless sheet panels
Product Discharge: 8"Ø flanged discharge - positioned at bottom center
Drive end endplate is welded, Idle endplate is bolted on for ribbon maintenance
7.37HP SEW Varibloc variable-speed gear unit with helical reducer
Supply: 154/440V, 60Hz, 3ph
Blender base footprint is 45"W X 60"L (included 94" elevating stand, welding will be required)

All carbon steel construction
Inside dimensions: 36"W X 104"L
Cast iron end plates (bolted)
Vertical pivot-gate discharge (12" X 8") on idle end
Incomplete drive components consist of a reducing roller chain and HTD belt sprocket
Motor not included
Base footprint: 50"W X 86"L
Total height: 96.5"

Manufactured by Romak Iron Works, Oakland CA. s/n 19433. Carbon steel construction. Trough dimensions: 36" W X 9' L X 42" deep. 4"Ø shaft. 15 HP Baldor motor, 1750 RPM, 230/460 Volt. V-belt drive with guard. Morse shaft mounted speed reducer, 15.22:1 ratio. 8"Ø center discharge. Test run video on file. Overall dimensions: 41" wide x 139" long x 72" high. Weight = 3,938 lbs.

Horizontal U-trough mixer lined internally with 1/4" stainless steel plate
Mixing chamber is 36"W X 108"L with a total depth of 42"
Non-rated full jacketing, approximately 68 sq.ft. surface area
Hinged, split top cover with 4"Ø port and 8" square cut-out
Drive: 15HP V-belt to torque-arm speed reducer (motor mounts to mixer bottom housing)
Current ribbon speed = 27 RPM.
6"Ø flanged, bottom-center end discharge (pneumatic dome valve included)
Base mounted, 46"W X 97"L floor area
Support stand has been saw-cut to ease shipping- will require certified welding repair
Base elevation to top of mixer is 118"
Service Power: 208-230/460V, 60Hz, 3ph AC
Video Available.

Reitz Jacketed Stainless Steel Double Ribbon Dual Agitator Blender
Model No: RDS-28-K3406
Serial No: RDS-780049
Jacket and Screws Rated for 14.9 PSIG
Metal Thickness: Trough - .1875, Jacket - .1875, Head - .375
(2) 25 HP Motors: 3 Phase, 230/460 Volt, 1770 RPM, Frame: 284T
Mixing Chamber Dimensions: 72" L x 57" W x 36" Deep
Hydraulic actuated hinged cover with 46"W X 48"D X 44"H stainless sheet plenum (previously insulated) with 4"Ø hose connection
Flooded capacity: 85 cu. Ft.
Ribbons are 28" Ø
Double End discharge.
Demonstration video on file. Agitator speed = 32 RPM.

Sanitary design - polished stainless steel material contact surfaces with bottom-center discharge (10"Ø flanged)
Base frame is constructed of mild steel
Mix chamber dimensions: 40" wide X 96" long X 46" depth
Full top cover with bag-breaking station (removable grating and hinged cover)
30HP Gearmotor drive will require 230/460V, 60Hz, 3 phase AC power.
Inline speed reducer with 14:1 ratio.
Overall dimensions (excluding drive): 45"W X 135"L X 60"H

All stainless steel construction. Blender tub dimensions: 40" wide X 8'-0" long
Powered by a 7.5HP, 230/460 volt, 3 phase, Super E, washdown duty AC motor. Shipping Info: 138" X 47" X 68" 2,505 LBS
The legs are currently ~26-1/2" high, measuring from bottom of horizontal box tubing structure.
The outlet is 5"Ø flanged. The outlet currently has a reducing flange taking the size down to 3"Ø sanitary fitting. The clearance below the outlet is currently 10". If the reducing flange is removed, there would be 15" of clearance below the 5" outlet.

Constructed from plate gauge carbon steel
Mixing chamber inside dimensions: 38"W X 118.5L X 36"D
Bolted endplate centers for ribbon assembly removal & maintenance
Final speed of ribbon ~30 RPM

Serial No: 2011134-HD30
Designed for processing a maximum 50LB per cubic foot bulk density grain and concentrates
All mild steel construction
Mixing Tank Dimensions: 4'-3"W X 8'-4"L X 4'-9"D
Discharge: 10" X 12" flanged (located bottom center, idle end)
Manual rack & pinion gate installed with an additional side discharge
25HP TEFC Drive - 230/460V, 60Hz, 3ph AC
V-Belt and Double Reduction Chain Drive
Overall dimensions: 135" L x 81" H x 87" H
Weight = 4,820 LBS
Video Available

Overall Dimensions: 120" L x 69" W x 71" H
Tub Inside Dimensions: 86" L x 61" W x 65" Deep
39" dia. sheave
11" bottom outlet
22" dia. access door on both sides
60" dia. ribbon
20" dia. & 12" dia. inlet at top of unit
(2) Euchner safety switches on both hinges for top door access
Total weight: 4060 lbs
40 HP General Electric Motor: 230/460 Volt, 3 Phase, 1770 RPM, Frame: 324T
Falk Gear Reducer: Ratio 13.50:1
Approximate shaft speed of 12 RPM.
Chain drive with guard.

All stainless steel U-trough blending chamber with a sanitary finish on internal surfaces
A combination of outer paddles with an inside ribbon provides a greater range of batch sizes
Blender Dimensions: 54"W X 120"L X 61"D (0.181" wall thickness)
Three-section top cover with 16"Ø inspection hatch and 24" square cut-out
Product Discharge: 10"Ø flange (valve not included), 40.5" from floor elevation
Floor elevation to top cover: 105"
Drive: 60HP motor coupled to a helical-bevel gear unit with chain reduction drive
Supply Power: 208-230/460V, 60Hz, 3ph AC
Overall dimensions: 174" L x 88" W x 110" H.
Weight = 8,510 LBS.
Video Available.

All mild steel construction
54"wide X 10' long blending chamber
Product discharge: 12" sq. pneumatic slide gate (bottom center located)
Full top covering, 40" X 60" product inlet with roll-away cover and heavy screen
Cross-braced structural steel elevated stand
Power required: 230/460VAC, 60Hz, 3 phase
Base dimensions: 58" wide X 137" long

All carbon steel construction
Mixing chamber dimensions: 5'W X 15'-2"L X 5'-5"D
Full top covering with a 30" square cut-out and a 32" square covered inspection hatch
14" square discharge with manual gate and an 8"Ø flanged discharge that is blanked-off
Drive end endplate is welded, idle endplate is bolted on
40HP drive with triple-reduction: V-belt, Rexnord planetary gear reducer and chain
Supply: 460V, 60Hz, 3ph
Blender footprint is 69"W X 190"L, 88" floor to top cover
Weight of blender and drive = 12,238 LBS

Serial # G-3810
Model F
Heavy duty sanitary construction using twin 9"Ø augers that extends 25" beyond mixing chamber
Mounted above twin augers is reverse flow 16"Ø mixing ribbon auger with 48" length of installed flighting
32" wide X 96" long flanged mixing chamber that tapers into a flared trough with partial center divide
Approximate capacity: 50 cubic feet
Discharge transitions thru a singe 4"Ø sanitary fitting
10HP washdown gearmotor drive with chain to a reduction gearbox with 3 outputs
Supply: 230/460V, 60Hz, 3 ph
Installed to a portable base frame assembly
Overall dimensions: 60"W X 156"L X 54"H
Weight = 2,850 lbs.
Demonstration Video on File.