Used and Surplus Hammermills

Design specification: Corn (40PCF) to 150 cubic foot per hour
Quantity of 32 pivoting hammers (1/4" thick)
Installed with 4-bar magnet at product inlet (7" square)
Two-section skid base is 19"W X 50"L
10HP belt drive
Power required: 208-230/460V, 60Hz, 3ph
Electronic copy Owners Manual on file
Demonstration Video on File.
Overall dimensions: 52" L x 28" W x 52" H
Weight = 1289 lbs.

Stainless Steel Material Contact Parts

Inlet: 6" Ø (w/ transition) OR 13" X 7" (w/o transition)
Outlet: 6" Ø (w/ transition) OR 13" X 7" (w/o transition), Outlet Height: 31" (to ground)
Stainless Steel Base: 52" X 34", Overall Height: 61" (ground to inlet), Weight: 865 lbs.

Leeson Motor: 230/460 V, 20 HP, 1755 RPM

(4) rows of swinging hammers.
Hammers are rated at +95% life. The side currently being used for crushing is 100%,
The lower liners are 100%, the upper liners are at least 50-75% worn near the rotor.
New bearings installed. New motor and coupling 2019.
5/8" perforated grate installed (different size grate available upon request)
New 20hp, 1200rpm, Lincoln motor, 3/60/230/460, TEFC, 286T

Stainless steel construction
Reversible chamber with fixed, stepped blades
Outboard pillow block bearings
6"Ø product inlet
Installed to a stainless frame with casters
Inverter-duty 30HP belt drive
Supply: 208-230/460V, 60Hz, 3 phase

24"Ø x 18" wide rotor with 1/4" thick X 2" wide swinging hammer clusters
13.5" X 19" flanged product inlet that cascades flow across a plate magnet before entering milling chamber
Optional discharge thru an 8" pneumatic slide gate or 4"Ø blow-thru adapter sleeve
Extra screens included
Mounted on a welded structural steel base measuring: 38" X 60"
Mill shaft direct-couples to a 30HP, 1765RPM TEFC motor
Supply: 230/460 volts

Stainless steel construction
Reversible chamber with fixed, stepped blades
Outboard pillow block bearings
6"Ø sanitary flanged product inlet/outlet
Installed to carbon steel stand
40HP direct-drive, 3545RPM TEFC motor
Supply power: 208-230/460V, 60Hz, 3 phase
Demonstration Video on File.

This hammermill was involved in a warehouse fire and is being sold as parts only. S/N-0.122 5666.  Grinder is designed to grind paper and cardboard. Pinch roller feeder system mounted on the unit.  1/2" diameter perforated plate.  Unit has a Marathon Blue max inverter duty type 50 HP 3550 RPM motor.  Variable from 1 hz to 75 hz and 326T frame.  Pinch roller feed drives are Marathon Blue Max 2 HP 1750 RPM inverter duty series.  Gear reducers on pinch rollers are by Boston Gear catalog # FF72630B76, with a ratio of 30.  Input HP maximum is 1.5.  The milling chamber is 8-3/4" inside dimension. There are (9) rows of 6 hammers per row. Also note the replaceable screen which is installed. Manufactured by Kamas Industri AB, Sweden. The main drive motors were electricall test run on may 1 and found to run.

This hammermill was involved in a warehouse fire and is being sold as parts only. S/N-0.122 5666.  Grinder is designed to grind paper and cardboard. Pinch roller feeder system mounted on the unit.  1/2" diameter perforated plate.  Unit has a Marathon Blue Max inverter duty type 50 HP 3550 RPM motor.  Variable from 1 hz to 75 hz and 326t frame.  Pinch roller feed drives are Marathon Blue Max 2 HP 1750 RPM inverter duty series.  Gear reducers on pinch rollers are by boston gear catalog # ff72630b76, with a ratio of 30.  Input HP maximum is 1.5.  The milling chamber is 8-3/4" inside dimension. There are (9) rows of 6 hammers per row. Also note the replaceable screen which is installed. Manufactured by Kamas Industri Ab, Sweden. Test run video on file. The main drive motors were electricall test run on may 1 and found to run.

Designed for bi-directional rotor rotation
Max. RPM: 3,600
24"Ø x 14" wide rotor with swinging hammer clusters (extra screens are included)
9" X 14" flanged and sloped inlet directs material flow across a plate magnet before entering milling chamber
Open bottom discharge
Mounted on a welded structural steel base measuring: 38" X 60"
Mill shaft direct-couples to a 50HP, 1765RPM TEFC motor
Supply: 230/460 volts

24"Ø x 20" wide rotor with 1/4" thick X 2" wide swinging hammer clusters
8" square, flanged product inlet that cascades flow across an 18" X 5" rare earth plate magnet before entering milling chamber
Screen holding bracket (no screens included)
Mounted on a unitary base with vibration isolators
Mill shaft direct-couples to a 100HP, 3570RPM inverter-duty rated motor (no VFD included)
Supply: 460 volts

24"Ø x 20" wide rotor with 1/4" thick X 2" wide swinging hammer clusters
8" square, flanged product inlet that cascades flow across an 18" X 5" rare earth plate magnet before entering milling chamber
Screen holding bracket (no screens included)
Mounted on a unitary base with vibration isolators
Mill shaft direct-couples to a 100HP, 3570RPM inverter-duty rated motor (VFD controller not included)
Supply: 460 volts

24"Ø x 24" wide rotor with 1/4" thick X 2" wide swinging hammer clusters
8" square, flanged product inlet that directs flow across an 18" X 5" rare earth plate magnet before entering milling chamber
Mounted on a unitary base with vibration isolators
Heat sensors installed on bearings
Mill shaft couples to a 100HP inverter-duty rated motor (no VFD included)
Supply: 460 volts
Overall dimensions: 85" long x 52" wide x 65" high.
Weight = 4,023 lbs.

Infeed size: 37"w X 34" long. AC drive: 200HP, 460 volt, 1780RPM, 60Hz, 3 phase. Rotor: 30"Ø X 31" wide (4 rows with 8 swing hammers each).

24" wide X 36" diameter rotor with 2.25"W X 10.5"L X 1.25"thk swing hammers
23" x 16" product inlet opening
Front side access to milling chamber and bottom screen
4"Ø air-draw vent port
Installed with multi-groove sheave and flywheel [Drive Required]
Heavy duty cast iron split housing with 40" X 40" base footprint